Fulton-performance KX15500301 User Manual
Browse online or download User Manual for For the car Fulton-performance KX15500301. Fulton Performance KX15500301 User Manual
- Page / 10
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
F3294-00 (Rev-B-16437) 12/11
• Purchaser/owner must ensure that product is
installed according to these instructions. Pur-
chaser/owner must not alter or modify product.
• Operator and bystanders should never position
any part of body under any portion of this prod-
uct or the load being supported.
• Do not allow children to play on or around this
product or the load being supported.
• Do not use winch to move humans.
• Do not get oil or grease on the friction discs.
This could allow the load to slip or fall.
• Obey crank rotation decal and operating
instructions.
• Never exceed maximum rated capacity. Refer
to stamped markings or decals on product to
obtain rated capacity. If uncertain, contact
Cequent Performance Products at 1-800-632-
3290 or www.cequentgroup.com
• Always inspect the cable and its attachment
before each use to make sure they are not
damaged. Never use worn, kinked, or frayed
cable. If the cable or attachment breaks, the
cable will whip violently, causing property dam-
age, serious bodily injury, and/or death.
• Never stand along side the winch cable or rope
or guide the cable or rope with your hands.
•Never operate with slippery, wet, or oily hands
and always maintain a firm grip on the winch
handle. Do not attempt to stop a winch by
grabbing the handle while in motion.
• Always maintain a minimum of three (3)
complete wraps of cable or rope on the drum.
• Only winches that have a minimum hub
diameter of 1 3/4” can accommodate steel cable.
• Assure there is adequate safety factor, of at least
3 times the maximum load for all components
used.
• A loud clicking sound from the ratchet must be
heard when lifting the load. If a loud clicking
sound is not heard, do not use and replace
ratchet components immediately.
• Never release the crank handle unless the
ratchet pawl is fully engaged and the load is
supported.
• Never leave a weight supported from the winch
while the winch is unattended, as another person
may attempt to operate the winch, thereby
creating an unsafe condition.
• This winch is designed for manual operation
only and the load rating is based on an
intermittent duty cycle.
• Excessive force in turning winch handle may
indicate overload. Winches require maximum
of 45 lbs of handle force to pull their rated load.
• If you cannot crank the winch with one hand
you are potentially overloading the winch.
• Periodically check mounting hardware for
proper torque and tighten if necessary.
• Always replace bent, broken, or worn parts
before using this product.
Installation Instructions
Warning: Failure to follow these warnings and instructions may result
in property damage, serious bodily injury, and/or death.
Read, Understand, Follow and Save These Instructions
Work Winches
Read, understand and follow all of these instructions and warnings (Instructions) before installing and using this product. Install and use this product only
as specified in these instructions. Improper installation or use of this product may result in property damage, serious injury, and/or death. Never allow
installation or use of this product by anyone without providing them with these instructions. You must read, understand and follow all instructions and
warnings for any product(s) to which this product is used in conjunction with or installed. Save these instructions with the product for use as a reference
for any future installation and use of the product.
(Mounting hardware not supplied.) The winch stand must be capable of supporting at least five times the rated capacity of the winch. The mounting
surface must be equal to or greater than the footprint of the winch frame. When attaching the winch, use 3/8” dia. grade-5 hardware and torque to 28-
30 ft-lbs. Mounting bolts will vary in length for each application. Check the final installation and make sure it winch is secure to mounting structure.
Line direction
K2550 Winch
(Cable wraps beneath drum)
Required
Line direction
Wrap guide for K1550,
KX1051, and K1051
(Cable wraps over top of drum)
Attaching a Rope:
Attaching a rope to the winch drum requires no bolts, nuts, or clamp. The
rope must weave through the drum outer wall and be secured beneath itself as
shown in the illustration.
Attaching a Steel Cable to a Drum:
Pass the cable from the inside of the drum through one of the dimpled holes
in the outer plate. Loop the cable around the drum bearing, under itself, and
leave 1” of cable extending past the clamp location. Torque the clamp nuts to approximately 2 ft-lbs.
Attaching a Handle:
Assemble the handle onto the flatted input shaft end. Tighten the 1/2”-13
locknut against the handle and torque to 22-25 ft-lbs. Do not over
torque. Do not adjust the double locknuts on the long end of the input
shaft.
Rope
Cable
Illustration only. Do not remove drum to install cable or rope.
Cable
Keeper
Drum
Bearing
Outer
Plate
®
WARNING
Failure to follow these warnings and instructions may result
in property damage, serious bodily injury, and/or death.
Input
Shaft
Handle
Locknut
Handle
Drum
Hub
Ratchet
Pawl
Double Locknut
Frame
- Work Winches 1
- How to Order 2
- Limited Five Warranty 2
- Operation 2
- Prior to Use 2
- Maintenance 2
- Treuils de Travail 3
- Garantie limitée de cinq ans 4
- Opération 4
- Avant l'utilisation 4
- Entretien 4
- Comment commander 4
- Cabrestante Manual 5
- Cómo Ordenar 6
- Funcionamiento 6
- Antes de Usar 6
- Mantenimiento 6
- Arbeitswinden 7
- Bestellen 8
- Betrieb 8
- Vor dem Gebrauch 8
- Wartung 8
- Handlieren 9
- Vijf jaar beperkte garantie 10
Summary of Contents
Page 1 - Work Winches
F3294-00 (Rev-B-16437) 12/11 • Purchaser/owner must ensure that product is installed according to these instructions. Pur-chaser/owner must not alter
Page 2 - Maintenance
Gebruik bij reparaties uitsluitend onderdelen van Cequent Performance Products of onderdelen van vergelijkbare kwaliteit. Vervangende onderdelen zijn
Page 3 - Treuils de Travail
Use only Cequent Performance Products’ parts or parts of equal quality for repair. Replacement parts are available through Cequent Performance Produc
Page 4 - Comment commander
F3294 (Rev-B-16437) 12/11 • L’acheteur/le propriétaire doit s’assurer que le pro-duit est installé conformément à ces instructions. L’acheteur/le pr
Page 5 - Cabrestante Manual
Pour les réparations, utiliser uniquement des pièces provenant de Cequent Performance Products ou de qualité équivalente. On peut se procurer des pièc
Page 6 - Mantenimiento
Eje de Entrada Arandela de Seguridad del Manubrio Manubrio Carrete Rotor Gatillo del Trin-quete Marco F3294 (Rev-B-16437) 12/11 • El comprador/propiet
Page 7 - Arbeitswinden
Use únicamente productos de remolque Cequent, o partes de igual calidad, para la reparación. Estos se pueden adquirir al contactar al Departamento de
Page 8 - Wartung
F3294 (Rev-B-16437) 12/11 • Der Käufer/Besitzer hat sicherzustellen, dass dieses Produkt gemäß dieser Anleitung montiert wird. Der Käufer/Besitzer d
Page 9 - Handlieren
Verwenden Sie ausschließlich Originalteile von Cequent Performance Products oder gleichwertig für Reparaturen. Austauschteile sind über die Kundendien
Page 10 - Vijf jaar beperkte garantie
Aandrijfas Hendel borgmoer Hendel Trommel Naaf Palrad Frame F3294 (Rev-B-16437) 12/11 • Bij ingebruikstelling van dit product dient koper/bezitter dez
© 2020, manymanuals.com. All rights reserved. | 2.172 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals