Fulton-performance 1413230134 User Manual download pdf

Before mounting the jack confirm that there will be no interference from the tow vehicle, tongue, ground, and any other mounted accessories while

stationary or in motion. Before installing, check for interference in all positions including handle swing and swivel positions. Check for interference

again after installation is complete. The height of the swivel mount is pre-set and torqued by the factory at a common height for most applications.

Read, Understand, Follow and Save These Instr uctions

• This product must be installed and used in strict

accordance with these instructions. Purchaser/

owner must not alter or modify the product.

• Operator and bystanders should never position

any part of body under or on the path of any

portion of this product or the load being

supported, or moved.

• Fully retract and rotate jack into its stowed

position before towing.

• This product is not intended to be used as a

transport device for the implement it is attached

to. Minimize movement of implement while jack

is under load.

• Do not allow children to play on or around this

product or the load being supported, or moved.

• Secure the load, vehicle and trailer from rolling

(by blocking wheels) when operating jack or

coupling trailer.

• Never exceed maximum rated capacity. Refer to

stamped markings or decals on product to obtain

rated capacity. If uncertain, contact Cequent

Trailer Products at 800-604-9466 or

www.cequentgroup.com.

• These jacks are designed for vertical loading.

Excessive side forces may cause jack failure and

must be avoided.

• Before manually moving trailer, crank to lowest

position.

• Lock the plunger pin into a hole in the mounting

bracket before raising or lowering the tongue.

• These jacks are not designed for mounting to

round tongues.

• Do not cut, drill, weld or modify this jack in any

manner not described in these instructions.

• All welding must be performed by an AWS

certified welder.

• Always replace bent, broken, or worn parts before

using this product.

Read, understand and follow all of these instructions and warnings (Instructions) before installing and using this product. Install and use this product only as

specified in these instructions. Improper installation or use of this product may result in property damage, serious injury, and/or death. Never allow installation

or use of this product by anyone without providing them with these instructions. You must read, understand and follow all instructions and warnings for any

product(s) to which this product is used in conjunction with or installed. Save these instructions with the product for use as a reference for any future

installation and use of the product.

Failure to follow all warnings and instructions may result in product

failure, property damage, serious bodily injury, and/or death.

WARNING

Installation Instructions

Warning: Failure to follow all warnings and instructions may result in

product failure, property damage, serious bodily injury, and/or death.

Trailer Jack

F3576 (Rev-D 17805) 08/12

Mounting Plate

3/8-16 x 7/8 Lg bolt

Lock Washer

XXXXXXXXXXXXXX

XXXXXXXXXX

Weld-on:

Mounting Plate is included on Weld-On

models only.

All welding must be performed by an AWS

certified welder. Recheck the position of

the mounting plate according to the

precautions listed above and as shown in

diagram below. Position the plate with the

flat surface toward trailer. Align top of

mounting plate flush with top of trailer tube

and weld completely around using a 3/16”

fillet weld. The threaded holes in the

mounting plate may need to be masked for

painting or re-tapped, depending on trailer

finish requirements.

Adjusting Swivel Mount Height: (if necessary)

With jack removed from trailer, loosen the two swivel fasteners until the slide block moves freely along outer tube.

To access the upper bolt, be sure the swivel bracket is rotated in the horizontal (3” mounting) position as shown.

Adjust swivel mount to desired location and re-torque to 60-70 ft-lbs. After adjustment, check for proper swivel and

pin engagement.

U.S. Patent # D568575, D570072, D577175 and Patents Pending

1 2 3 4 5 6 7 8 9 10

Summary of Contents

Page 1 - WARNING

Before mounting the jack confirm that there will be no interference from the tow vehicle, tongue, ground, and any other mounted accessories while sta

Page 2 - Limited Lifetime War ranty

Beperkte levenslange garantie ("Garantie"). Cequent Trailer Products, Inc. ("Wij" of "Ons") garanderen uitsluitend de ee

Page 3 - ADVERTISSEMENT

Limited Lifetime Warranty (“Warranty”). Cequent Trailer Products, Inc. ("We" or “Us”) warrants to the original consumer purchaser only (&qu

Page 4 - Entretien

U.S. Patent # D568575, D570072, D577175 and Patents Pending Veuillez lire, comprendre, observer et conserver ces instructions. Il importe de lire, co

Page 5 - ADVERTENCIA

Garantie à vie limitée (« Garantie »). Cequent Trailer Products, Inc. (« Nous ») garantit à l’acheteur initial seulement (« Vous ») que le produit se

Page 6 - Mantenimiento

Gato para Remolques Lea, entienda, siga y conserve estas instr ucciones Lea, entienda y siga estas instrucciones y advertencias (Instrucciones) antes

Page 7 - ACHTUNG

Instrucciones de instalación (cont.) Con perno: Este gato se puede configurar para instalarse en tubos de remolque de 3” x 3” ó 3”x 4” únicamente. C

Page 8 - Montageanleitung (Forts.)

Vor Montieren des Stützbocks ist sicherzustellen, dass es weder bei Stillstand noch in Bewegung zu Behinderungen durch das Zugfahrzeug, die Deichsel,

Page 9 - WAARSCHUWING

Begrenzte Garantie auf Lebenszeit (“Garantie”). Cequent Trailer Products, Inc. (“wir“) garantiert ausschließlich dem Erstkäufer gegenüber (“Sie“) , d

Page 10 - Onderhoud

Alvorens de krik te bevestigen, controleer het lastvoertuig, de tong, de aardkabel en alle bevestigde toebehoren op storingen, zowel stilstaand als in